LG OLED65G7V Manual do Utilizador

P/No: MFL69649042 (1701-REV00)Printed in KoreaOLED TVOLED65G7* OLED77G7*www.lg.comAACR2032b X 2(M4 X L10) X 2 X 4a(M10 X L70)OLED65G7*OLED77G7*C X 18(

1212433 4132AA

A B C D E F OLED65G7V-Z1461 883 243 892 68 31.7OLED77G7V-Z1734 1055 317 1067 83 54.1Power requirementAC 100-240 V ~ 50 / 60 Hz120DBECAF*MFL69649042*

Please read this manual carefully before operating your set and retain it for future reference.www.lg.comSafety and ReferenceP/NO : MFL69727247 (1704-

2ENGLISHWarning! Safety instructionsCAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BA

3ENGLISH • Do not put or store inflammable substances near the product. There is a danger of combustion/explosion or fire due to careless handling of

4ENGLISH • Signal from Remote Control can be interrupted due to external/internal lighting eg Sunlight, fluorescent lighting. If this occurs turn off

5ENGLISHPreparing • If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few minutes.

6ENGLISHLifting and moving the TVPlease note the following advice to prevent the TV from being scratched or damaged and for safe transportation regard

7ENGLISHBasic functionsPower On (Press)Power Off (Press and hold)1Volume ControlProgrammes Control1 All running apps will close, and any recording in

8ENGLISHMounting on a wall(This feature is not available for all models.)10 cm10 cm10 cm10 cm(Only OLED65/77G7*)Attach an optional wall mount bracket

9ENGLISHProvided itemAV box fixing supporter / Wall mount spacerWall mount spacerx 2 x 2 x 2(Only OLED65/77W7V)Provided itemWall mount Punching Guide

10ENGLISHHow to attach to masonry wallsPlease follow the below direction.1 Use a drill bit Ø 8 mm to drill a hole for the anchor location within a de

11ENGLISHUsing the kensington security system(Only OLED65W7*)The Kensington security system connector is located at the rear of the Companion Box (AV

12ENGLISHOther connectionsConnect your TV to external devices. For the best picture and audio quality, connect the external device and the TV with the

13ENGLISHMagic remote functionsWhen the message “Magic remote battery is low. Change the battery.” is displayed, replace the battery.To replace batter

14ENGLISH1 2 Streaming Service buttons Connects to the Video Streaming Service. (INPUT) Changes the input source. - Pressing and holding the butto

15ENGLISHTroubleshootingCannot control the TV with the remote control. • Check the remote control sensor on the product and try again. • Check if ther

16ENGLISHGenerated Sound • “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contract

17ENGLISH(Depending on country)Digital TV Analogue TVTelevision systemDVB-TDVB-T2DVB-CDVB-S/S2PAL/SECAM, B/G, D/K, ISECAM LChannel coverage (Band)DVB

MODELSERIALRecord the model number and serial number of the TV.Refer to the label on the back cover and quote this information to your dealer when req

OWNER’S MANUALEXTERNAL CONTROL DEVICE SETUPwww.lg.comPlease read this manual carefully before operating the set and retain it for future reference.

2ENGENGLISH2KEY CODESKEY CODES• This feature is not available for all models.Code (Hexa)Function NoteCode (Hexa)Function Note00 CH +, PR + R/C Button

3ENGENGLISH3EXTERNAL CONTROL DEVICE SETUPEXTERNAL CONTROL DEVICE SETUP• Image shown may differ from your TV.Connect the USB to Serial converter/RS-23

4ENGENGLISH4EXTERNAL CONTROL DEVICE SETUPPhone jack Type• You need to purchase the phone-jack to RS-232 cable required for the connection between the

5ENGENGLISH5EXTERNAL CONTROL DEVICE SETUPCommunication Parameters• Baud rate : 9600 bps (UART)• Data length : 8 bits• Parity : None• Stop bit : 1

6ENGENGLISH6EXTERNAL CONTROL DEVICE SETUPTransmission / Receiving ProtocolTransmission[Command1][Command2][ ][Set ID][ ][Data][Cr][Command 1] : Firs

7ENGENGLISH7EXTERNAL CONTROL DEVICE SETUP* Commands may work differently depending on model and signal.01. Power (Command: k a) ► To control Power *On

4 5 612 3bOLED65G7*a5 mm

8ENGENGLISH8EXTERNAL CONTROL DEVICE SETUPData Min : 00 to Max : 64Ack [i][ ][Set ID][ ][OK/NG][Data][x]09. Tint (Command: k j) ► To adjust the screen

9ENGENGLISH9EXTERNAL CONTROL DEVICE SETUP1 0 05th Band1 0 1 0 020(decimal)Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]* It depends on model, and

10ENGENGLISH10EXTERNAL CONTROL DEVICE SETUPNumber - 22 : Antenna TV (DTV) – Don’t Use Physical Channel Number - 26 : Cable TV (CADTV) - Don’t Use

11ENGENGLISH11EXTERNAL CONTROL DEVICE SETUP24. Input select (Command: x b) (Main Picture Input) ► To select input source for main picture.Transmission

12ENGENGLISH12EXTERNAL CONTROL DEVICE SETUP27. Auto Configure (Command: j u) (Depending on model) ► To adjust picture position and minimize image sha

4 5 612 3OLED77G7*CC

79810OLED77G7*b

HDMI INLANUSB INAUDIO OUT/H/P OUTANTENNA /CABLE INSatellite INOPTICAL DIGITAL AUDIO OUTPCMCIA CARD SLOTHDMI IN/ARCCOMPONENT INAV INVIDEOVIDEO L/MONO A

HDMI INLANUSB INAUDIO OUT/H/P OUTANTENNA /CABLE INSatellite INOPTICAL DIGITAL AUDIO OUTPCMCIA CARD SLOTHDMI IN/ARCCOMPONENT INAV INVIDEOVIDEO L/MONO A

HDMI INLANUSB INAUDIO OUT/H/P OUTANTENNA /CABLE INSatellite INOPTICAL DIGITAL AUDIO OUTPCMCIA CARD SLOTHDMI IN/ARCCOMPONENT INAV INVIDEOVIDEO L/MONO A